(1) The Electrical Safety Policy provides overarching principles for protecting the QUT community from being harmed and preventing property from being damaged by electricity. QUT uses a risk-based approach to conduct activities involving electrical work and electrical equipment in a way that is electrically safe. This approach is in accordance with relevant legislation, Australian Standards and codes of practice, with due regard for the health and safety of the QUT community and the environments in which it operates. (2) This Policy must be read in conjunction with the Electrical Safety Standard and supporting documents that detail, guide and address the practical elements of electrical safety at QUT. (3) This Policy applies to members of the QUT community who use, purchase, import, design, manufacture, modify and/or work with electricity or electrical equipment at the University, including: (4) This Policy does not apply to extra-low voltage electrical equipment. QUT Electrical Safety Standard provides information on voltage. (5) All members of the QUT community have a responsibility to promote electrical safety at QUT by being aware of the potential risks and implementing safety procedures when working with and around electricity. (6) The University expects that all electrical work will be performed in compliance with relevant legislation, codes of practice, QUT policy, supporting documents and Australian Standards (where applicable). (7) Electrical work must be: (8) Electrical equipment imported, purchased, designed, manufactured, hired, modified or loaned out, by any member of the QUT community, must follow QUT procedures and be assessed or tested as electrically safe before use. (9) No work on energised electrical equipment (i.e. live work) is to be carried out by any members of the QUT community. (Exceptions to this Policy are detailed in the Electrical Safety Regulation 2013 (Qld) s15 and s18). (10) Regular inspections and test and tag of electrical equipment is both a legislative requirement and one of the methods QUT uses to minimise electrical risk and enhance electrical safety. It is expected that visual inspections, prior to using electrical equipment will be performed. (11) A competent person, either a University staff member who has completed the approved training program or an approved contractor, must carry out electrical testing and tagging of specified electrical equipment at QUT. Further information can be found in the Electrical Safety - Inspection, Test and Tag Guideline. (12) Wherever possible, electrical equipment should be purchased from an Australian supplier or imported by an Australian company. This ensures that all electrical equipment and parts of the electrical equipment meet Australian legislative requirements and safety standards. (13) QUT has established procedures for the importation and purchase of electrical equipment which must be followed by all staff and students. Purchasing and importing overseas electrical equipment for activities at QUT must be done in accordance with QUT finance requirements. The Electrical Safety - Imported Electrical Equipment Checklist and other supporting documents have been developed to facilitate this. (14) Any incident involving electricity or electrical equipment must be reported to an immediate Supervisor, local Health, Safety and Environment personnel and to Health, Safety and Environment. This should be done via the HSE Hub (QUT staff access only), following QUT's incident reporting processes. This includes, but is not limited to, health, safety and environmental harm, incidents, and injuries (including near misses) and hazards involving electricity or electrical equipment. (15) If the electrical incident resulted in, or had the potential to result in, a death, serious injury to a person, a person receiving medical attention, or was a dangerous incident, QUT’s First Aid and Medical Emergency Procedures (QUT staff access only) must be followed and it must be reported immediately to Health, Safety and Environment (QUT staff access only) as it may be a notifiable incident. (16) Electrical safety legislation requires specific records to be retained throughout the lifecycle of any electrical equipment this includes records pertaining to design, manufacture, importation, maintenance, testing and disposal. (17) To assist members of the QUT community to meet their legislative obligations, Health, Safety and Environment has developed a retention and disposal schedule for all Health, Safety and Environment-related records. (18) Failure to follow safe systems of work, misuse of electrical equipment, damaging or bypassing electrical risk control measures, performing unlicensed electrical work can lead to severe fines or prosecution under the Work Health and Safety Act 2011 (Qld), the Electrical Safety Act 2002 and other relevant legislation, and will also be dealt with under the QUT Code of Conduct - Staff, Enterprise Agreements and Employment Conditions, the QUT Code of Conduct - Student and/or the Grievance Resolution Procedures for Student Related Grievances policies.Electrical Safety Policy
Section 1 - Purpose
Section 2 - Application
Section 3 - Roles and Responsibilities
General
Top of Page
Section 4 - Electrical Work Requirements at QUT
Section 5 - Inspection, Test and Tag of Electrical Equipment
Section 6 - Purchase and Importation of Electrical Equipment
Section 7 - Reporting of Incidents Involving Electricity or Electrical Equipment
Section 8 - Records Management
Section 9 - Failure to Comply
Section 10 - Definitions
Term
Definition
Authorised Visitors
As defined in the Health, Safety and Environment Policy.
Electrical Equipment
Within this Policy means any machinery, equipment and instrumentation that is operated by electricity at a voltage greater than extra-low voltage. The Electrical Safety Act 2002 (Qld) s14 contains a full definition of electrical equipment.
Electrical Risk, Electrically Safe and Electrical Safety
Are defined in the Electrical Safety Act 2002 (Qld) s10.
Electrical Work
Refer to Electrical Safety Act 2002 (Qld) s18.
Energised (Live) Electrical Work
Means electrical work above 50VAC or 120V DC carried out in circumstances where the part of electrical equipment being worked on is connected to electricity or ‘energised’.
Extra-Low Voltage
Means voltage that does not exceed 50 volts alternating current (50 V AC) or 120 volts ripple-free direct current (120 V ripple free DC) e.g. mobile phone, laptop/tablet, e-reading device, any device that draws power through a USB cable, battery-operated tools etc.
Managers and Supervisors
As defined in the Health, Safety and Environment Policy.
Staff
As defined in the Code of Conduct - Staff.
QUT Community
As defined in the Health, Safety and Environment Policy.
View Document
This is the current version of this document. You can provide feedback on this document to the document author - refer to the Status and Details on the document's navigation bar.
Position
Responsibility
Director, Health Safety and Environment
Develops and approves all Health, Safety and Environment electrical safety-related documents.
Monitors and implements strategies to assist QUT to meet its electrical safety compliance obligations.
Determines if an electrical incident is notifiable and reports to the regulator within mandatory timeframes.
Provides direction and advice on electrical safety matters, to University officers, to enable them to meet their due diligence responsibilities.
Approves and issues electrical safety alerts to the QUT community.
Director, Facilities Management
Ensures all infrastructure and electrical equipment built, purchased, hired, or used for Facilities Management operations and activities meets Australian electrical safety legislation and standards.
Ensures any contractors or staff engaged to perform electrical work for Facilities Management operations are Australian-licensed or Australian-registered/certified and competent to perform the work.
Is responsible for the electrical infrastructure in QUT owned properties (and to various limited extents, property and facilities under lease arrangements) for the safe management and compliance of electrical systems, including installation, maintenance, testing and repair.
Maintains records of electrical infrastructure testing and maintenance.
Managers and Supervisors (within areas of responsibility)
Ensure all people within their care are suitably qualified and competent to use the equipment or carry out the work prior to using electrical equipment and/or performing electrical work.
Ensure test and tag of electrical equipment is carried out on a regular basis and all equipment is maintained in an electrically safe condition.
Records related to electrical equipment and electrical work (e.g. test and tag, purchase, maintenance, commissioning and disposal of electrical equipment) are retained for the requisite timeframes within QUT-approved records management systems.
Ensure local procedures are developed (where required) to manage electrical equipment and electrical work.
Electrical work (on equipment above extra-low voltage) for maintenance, research, or teaching purposes, is only carried out by Australian-licensed or Australian-qualified persons who have been duly authorised to do so.
Incidents and near misses involving electrical equipment or electricity are reported immediately to Department of Health, Safety and Environment and logged in the HSE Hub.
Electrical equipment brought into the University by staff or students is electrically safe, fit for purpose and, where required, has undergone test and tag before use.
All staff involved in the use, purchase, design, importation, manufacture, modification and disposal of electrical equipment
Are required to ensure all electrical equipment:
All other relevant members of the QUT community
Must comply with all relevant legislation, Australian Standards, QUT policies and supporting documents as relevant to electrical safety or as instructed by competent persons.
Should visually inspect electrical cords and equipment for any physical damage before use and report any suspect items to a Supervisor.
Must report any electrical incidents (actual or potential, i.e. near-miss) to immediate Supervisor and to the Department of Health, Safety and Environment via the HSE Hub as soon as practicable.